The Analisis Kinerja dan Akurasi Sensor Thermocouple Tipe K dalam Sistem Pengendalian Suhu Reflow Soldering
DOI:
https://doi.org/10.55606/jutiti.v5i2.5867Keywords:
Periodic Calibration, Precision Control, Solder Reflow, Temperature Sensor, Thermocouple TypeAbstract
The reflow soldering process is an important stage in the assembly of electronic components that requires high-precision temperature control to ensure the quality of the solder joints. This study aims to evaluate the performance of a K-type thermocouple temperature sensor integrated into the solder reflow control system. Evaluation was carried out through temperature measurements at 20 different points, ranging from 35°C to 220°C, with a focus on reading accuracy and error rate. The results of the experiment showed that the type K thermocouple sensor had an error range between 0.02°C to 0.97°C, with an average error value of 0.54°C. These findings indicate that the sensor is stable and reliable enough to be used in industrial applications that demand temperature precision. The advantages of these sensors lie in their cost efficiency, ease of integration, and responsiveness to temperature changes. Nonetheless, periodic calibration is still necessary to maintain long-term accuracy, especially in dynamic work environments. This research contributes to the development of temperature control systems in the electronic manufacturing process, especially in the selection of the right sensors to support production quality. The conclusion of this study confirms that the K-type thermocouple is a practical and economical solution in reflow soldering systems, with sufficient performance to meet industry standards.
Downloads
References
Conseil-Gudla, H., Li, F., & Ambat, R. (2021). Reflow Residues on Printed Circuit Board Assemblies and Interaction with Humidity. IEEE Transactions on Device and Materials Reliability, 21(4), 594–602. https://doi.org/10.1109/TDMR.2021.3120941.
Depiver, J. A., Mallik, S., & Harmanto, D. (2021). Solder joint failures under thermo-mechanical loading conditions–A review. Advanced Materials and Processing Technology, 7(1), 1–26. https://doi.org/10.1080/2374068X.2020.1751514.
Guo, Y., Liu, M., Yin, M., & Yan, Y. (2022). Reliability Sensibility Analysis of the PCB Assembly concerning Warpage during the Reflow Soldering Process. Mathematics, 10(17). https://doi.org/10.3390/math10173055.
Ko, K. W., & Cho, H. S. (2000). Solder joints inspection using a neural network and fuzzy rule-based classification method. IEEE Transactions on Electronics Packaging Manufacturing, 23(2), 78. https://doi.org/10.1109/6104.846932.
Kus, A., Isik, Y., Cakir, M. C., Coskun, S., & Özdemir, K. (2015). Thermocouple and infrared sensor-based measurement of temperature distribution in metal cutting. Sensors (Switzerland), 15(1), 1274–1291. https://doi.org/10.3390/s150101274.
Lam, T. L. (2021). Low-Cost Non-Contact PCBs Temperature Monitoring and Control in a Hot Air Reflow Process Based on Multiple Thermocouples Data Fusion. IEEE Access, 9, 123566–123574. https://doi.org/10.1109/ACCESS.2020.3036527.
Lim, I. S. S., Chung, E. C. Y., Tan, K. B. T., & Teoh, K. S. (2015). The practicality of TRIZ based conceptual solutions in solving tombstoning defects during SMD soldering. Chemical Engineering Research and Design, 103, 123–129. https://doi.org/10.1016/j.cherd.2015.09.012.
Ma, G., Huang, X., & Liu, S. (2021). Heat Transfer Modeling and Oven Temperature Curve Optimization of Integrated Circuit Board Reflow Soldering. IEEE Access, 9, 141876–141889. https://doi.org/10.1109/ACCESS.2021.3120496.
Septiana, R., Roihan, I., & Koestoer, R. A. (2021). Denoising MAX6675 reading using Kalman filter and factorial design. International Journal of Electrical and Computer Engineering, 11(5), 3818–3827. https://doi.org/10.11591/ijece.v11i5.pp3818-3827.
Tang, X. Q., Zhao, S. J., Huang, C. Y., & Lu, L. K. (2018). Thermal stress-strain simulation analysis of BGA solder joint reflow soldering process. Proceedings - 2018 19th International Conference on Electronic Packaging Technology ICEPT 2018, 981–986. https://doi.org/10.1109/ICEPT.2018.8480615.
Tsai, T. N. (2012). Thermal parameters optimization of a reflow soldering profile in printed circuit board assembly: A comparative studi. Applied Soft Computing Journal, 12(8), 2601–2613. https://doi.org/10.1016/j.asoc.2012.03.066.
Wahono, W. T., Winarno, T., & Fathoni, F. (2020). Implementasi Fuzzy Logic Untuk Pengontrolan Suhu Pada Proses Reflow Oven Soldering. Jurnal Elektronika dan Otomasi Industri, 3(1), 2. https://doi.org/10.33795/elkolind.v3i1.59.
Yang, W., & Chung, D. D. L. (2021). Effect of temperature on the electrical conduction and dielectric behavior of solder. Journal of Materials Science: Materials in Electronics, 32(5), 6511–6519. https://doi.org/10.1007/s10854-021-05369-9.
Yi, S., & Jones, R. (2020). Machine learning framework for predicting reliability of solder joints. Soldering and Surface Mount Technology, 32(2), 82–92. https://doi.org/10.1108/SSMT-04-2019-0013.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Jurnal Teknik Informatika dan Teknologi Informasi
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
